Bathroom Sink Drain Stopper

Having an old bathroom sink that causes a lot of trouble can be a bit frustrating. Maybe your old bathroom sink is leaking, or has a stopper that does not work. Rather than fixing it, it is always better to install a new one. You do not have to call professional plumbing service to do this since it can cause a lot of money. Bathroom sink drain installation should be easy if you know how to do it. However, if you are not confident doing it on your own, it would be wiser for you to call a plumber.

First of all, you need to choose a new drain with the same diameter as the old one. You’re free to choose whatever style you like. Begin the bathroom sink drain installation by cleaning the areas underneath the sink so that you have an empty space to begin the work. Loosen the cap that connects the drain and the pipe so that the drain will be disconnected. Then, you should loosen the nut located at the end of the drain pipe underneath the sink so that the drain can be pulled out. Put the nut and the wedge shaped seal on the new drain pipe in the same way. However, if you break the seal accidentally, you can always buy a new one in the nearest hardware store.

Once the sink is removed, clean the crud around the edge. Use caulking from a tube and turn over the drain flange so that the bottom faces up. Make sure to apply the caulking in the area underneath the drain flange. Insert the flange into the drain and turn it clockwise then hold it in position for few minutes. Last but not least, you need to install the sink basket. Simply insert the tailpiece into the flange and turn it clockwise to tighten. Put on the nut and tighten it. Attach the pipe into its original position then attach it to the bottom of the drain.

By following the simple steps given above, you can easily install a new bathroom sink drain on your own. Every homeowner can install new bathroom sink by using simple home tools without any hassle. If you follow the steps accordingly, it should not leak or cause other problems. However, you should check for any leaks by turning on the tap when you have finished installing. There is a possibility that some of the parts are not installed properly.

Every homeowner should know how to do bathroom sink drain installation [http://sinkdraininstallation.com/bathroom-sink-drain-installation/]. This will save you a lot of money and make you more skillful in handling household mechanical issues. For more information about sink drain installation [http://sinkdraininstallation.com/] please visit our site.

One of the nastiest most disgusting places on the face of the earth lies in your bathroom sink drain. I don’t know a child, or adult, brave enough to stick their fingers down the dark hole. Unfortunately it is also a place where lots of nasty things get stuck so they typically are always in need of cleaning. This article will explain how the drain works, how to clean it, and how to replace it with new parts. Believe it or not, except for the nastiness factor, this is a relatively easy job that anyone can handle.

The first thing to do is clear out the cabinet underneath the sink, all of it. The more room you have the work on these parts the easier your job will be. If you look directly under the sink you will see an inch and a half pipe come down and bend back to the wall. This bend is called a P trap. The P trap always has water in it to allow no gas to come back from the sewer line, which means no smell. If the P trap wasn’t there you would have a sewer smell throughout your whole house. This is one of the main places that clogs can happen as everything has to go through that bend. Removing it is easy, loosen all the plastic nuts around the drain pipe. This will allow you to slide the pipes apart and remove the P trap. It is a good idea to have a small bucket or container to catch the water still in the P trap. I would recommend replacing the P trap as they aren’t very expensive and the new one comes with all new seals.

Now there should be a straight piece of pipe coming out of the bottom of the sink with a small nut and rod coming out the back. If you remove this nut the rod should pull straight out. This rod allows the drain stopper to move up and down. With the rod out the stopper should pull out of the top of the sink. If yours is like most sinks, there is probably a lot of hair and gunk stuck to it. This is the other area where a sink backs up most often. There is no easy way to clean this part except just to do it. Scrub it down good with some cleaner so no particles are left sticking to it.

Look for all the pipes to make sure there are no obstructions and reassemble all the parts you removed. Replace all the seals and hand tighten the nuts around the pipe, close the stopper, fill the sink with water, and open the stopper. Check for any leaks under the sink. If it’s dry you have done the job correctly.

Article Source: http://EzineArticles.com/6489559

Bathroom Sink Drain

Proper installation is the key for your bathroom sink drain to function well in the long run. As the time goes by, the pipes and drains will loosen and leak. Based on this fact, it is recommended that you perform proper installation to ensure durability. Additionally, you should also use high quality parts and materials. You also need to make sure that you also avoid mistakes in the installation process. Otherwise, your bath sink drain will not work properly and early leakage may also occur. Here are some common installation mistakes that you should avoid:

1. When installing the drains, you have to be sure that the connections are fastened tightly. However, don’t tighten the connections too securely since it can cause cracking and strain. It can also cause warping, which will allow water to pass through. Most people fasten the connections too tightly and cracking happens afterwards. You should also check the washers since they have the task to close air leakage on the pipe.

2. Sometimes, people don’t really pay attention to the materials used to manufacture the parts when installing bathroom sink drain. Stainless steel is the recommended material since it offers more durability than any other materials. If you buy the drain set separately, do check if the other parts are also made of stainless steel.

3. Don’t pour cleaning fluids that contain strong acids into the drains since they can cause corrosion. Otherwise, corrosive acids can cause your drain to leak in the future.

4. Don’t cut the plastic pipes too long or too short. If the pipes are too long, they will overlap and tend to be out of alignment. When you cut the pipes too short, it will cause water to seep out and the drains will gradually leak.

5. You should clean your bathroom sink drains regularly if you expect them to work properly. You don’t need to disassemble the drains when cleaning but you can do it if regular cleaning is not performed. Make sure that you also don’t use hazardous cleaning materials since they will only damage the drains. Hot water is the right cleaning medium since it will prevent serious clogging.

6. Cracking and leaking will still happen even if you perform regular maintenance. Therefore, performing the necessary precautions during and after installation is essential. Hence, the sink drains can last longer. If you find that the drains eventually start to leak, replacing them altogether is the best solution. It is because replacing some parts for short term use will only cost you more money in the future.